Lõi lọc Zipwater 93702
- Công nghệ: HF
- Bảo hành: 3 tháng
Bộ lọc Zip MicroPurity kích thước mao quản 0.2 micron dành cho máy Hydro tap.
Công suất lọc 6.813 lít, lưu lượng 5.678 lítt/ phút.
Đạt chứng nhận NSF42 và NSF53
Zip MicroPurity 0.2 micron filter for Commercial HydroTaps and Chilled water products
6,813 Litres filtration capacity @ flow rate 5.678 l/min
Independently tested and certified by NSF 42 (aesthetic effects) and NSF 53 (health effects) standards.
LIÊN HỆ NGAY ĐỂ NHẬN ƯU ĐÃI TỐT NHẤT
Máy lọc nước cao cấp nhập khẩu
- 0243-999-1456
- info@aulac.net.vn
- Chi tiết
- Thông số kỹ thuật
- Tính năng nổi bật
- Vận hành lắp đặt
Chức năng lọc của lõi ZipWater:
- Giảm vi khuẩn
- Loại bỏ cặn bẩn kích thước lơn hơn 0.2 micron
- Loại bỏ Clo dư.
- Giảm độ cứng
- Loại bỏ chỉ , cải thiện mùi và vị của nước.
Đạt tiêu chuẩn NSF 42 và NSF 53
Reduces:
Bacteria growth
Sediment > 0.2 micron Chlorine, taste & odour Cryptosporidium and Giardia Lead
Limescale
The filter also contains a naturally occurring antimicrobial that is used to prevent bacteria growth inside the filter.
Meets the standards of:
AS/NZS 3497 WM-035001
Including AS/NZS 4348
Mã đặt hàng sản phẩm 93702 thay thế cho các dòng máy ZipWater nóng lạnh thương mại sản xuất sau năm 2017
Giảm vi khuẩn
- Loại bỏ cặn bẩn kích thước lơn hơn 0.2 micron
- Loại bỏ Clo dư.
- Giảm độ cứng
- Loại bỏ chỉ , cải thiện mùi và vị của nước.
Đạt tiêu chuẩn NSF 42 và NSF 53
Reduces:
Bacteria growth
Sediment > 0.2 micron Chlorine, taste & odour Cryptosporidium and Giardia Lead
Limescale
The filter also contains a naturally occurring antimicrobial that is used to prevent bacteria growth inside the filter.
Meets the standards of:
AS/NZS 3497 WM-035001
Including AS/NZS 4348
Theo hướng dẫn sử dụng.
- Go to filter flush in the menu, this isolates the water supply. Variations apply depending on the product. Refer to individual instruction.
- Relieve system pressure via the filter flush stop cock if provided, a quick open and close will do. Use the bucket to catch the discharge.
- Grasp filter cartridge, rotate the cartridge a quarter turn to the left and gently pull down.
Caution: a small amount of water will drip as the cartridge is removed. Do not tilt the cartridge as water may spill from it if tilted.
- Unpack replacement cartridge, write today’s date where shown on the label and remove the sanitary cap.
Avoid touching the filter O-rings and filter opening as this may cause bacterial contamination of the cartridge.
- Push the new cartridge in and up into the filter head.
- Turn the cartridge a quarter turn to the right until the cartridge comes to complete stop and is locked into position.
- Locate the filter flush hose (if provided) situated behind the filter cartridge and direct the hose into a container ready for flushing. Open the filter flush stop-cock. On the menu press Adjust or Start, this will start the water flow, flushing the cartridge. Allow at least 10 litres of water through the cartridge before use, to activate the filter. Isolate the filter flush stop-cock and re-fit behind the filter cartridge. Now stop filter flush or press filter flush off to stop the flow. (It may take approximately 3 minutes to flush the 10 litres.)
- Wipe up any spills and dispose of spent filter cartridge and packaging thoughtfully.
- If your unit is a G4 HydroTap with a touch screen. Go to Menu >Install>Filter Reset >reset internal filter. Or in G3 HydroTap scroll through the menu to “Litres Filtered”, press adjust to reset litre counter. Press adjust and it asks “are you sure”. Press adjust again to lock in the command.
- Scroll through the menu to “Filter Used (Days)”, press adjust to reset the timer. Press adjust and it asks “are you sure”. Press adjust again to lock in the command. After approx 10 seconds it will default to the selected mode.
- Close the door to secure the appliance.